Відео

👍👍

I steer clear of Victor-Reinz. Rebuilt a BBC a couple years ago. The rear main looked funny to me. I measured it. It was .020" too big on the crank side. Had I not noticed that, can you imagine how much oil would have been dumped all over the clutch, bell housing, and floor? Then pulling the motor again and replacing it and everything else to get to it? I "attempted" to contact Victor Reinz. US offices, European office, e-mails... I got no response. Totally unacceptable. The vendor I bought the gasket set from? They said the only way they could do anything was to return the entire gasket set... Resolution? Bought a Felpro rear main at the local parts store. What a fiasco. I won't buy Victor-Reinz unless I am in a spot where it is the only brand available.

No dialog wtf 😂😂😂😂😂 joke video

Great and clean job! I'm in love :-)

Why not roll the cart closer to your work? lol

@1:25 . I was wondering why she added electric tape. Then I realized that’s they cam sprocket’s key way, which does have sharp edges.. good tip!

Merci ❤❤ dieu vous protège

Great video, Victoria!

Try doing this on an n52 engine, no chance but I appreciate her calming smile whilst I'm losing it because it's keeps popping out

Happy mechanic because she has all the special tools 😂. Meanwhile the rest of us have to use our wits to get the job done

Here's a lesson I could have used 20 years ago.

So, the integrated rotary shaft seal must be coming out soon, right?

Hahaha was that meant to be legit or a Zoolander parody? For people who can’t mechanic good 😅 start by replacing those sick poses with the critical information and several steps you missed/shouldn’t have done

she is either the strongest girl in the world or they are the loosest exhaust manifold bolts ever

Nice to see the gender role being broken. It is possible to work clean. A good technoque for pressing in the oil seal, much better than hammering and hoping. However, the number of special tools used to get to the oil seal shows how out of touch modern car design is from the folk who have to work on their stuff...by design of course

What a stupid worthless video. Some commentary would have been so much better than that music. Evplain which way the gasket goes on. What was she spraying on it to clean it.

I was hoping to see a better design of the dispenser end so that u don't use it once and it hardens up that u cannot squeeze any out next time u use it. This video is useless.

This is exactly how it worked for me but then I woke up from my dream ..

Do not touch cleaned area with fingers, you could leave fingerprints or grease from the fingers. Engine must be rotated few revolutions with PTFE seals installed to leave sealing material on shaft and after that engine must be turned off for 4 hours in certain temp range. This video is not explaining the right procedure so do not follow this.

good afternoon and in the gas tank you can use it in contact with gasoline, thanks

Добрый день, скажите а в бензобака можно его использовать, спасибо

Can someone confirm if the bolts should be oiled? I’m worried lubricating the treads would alter the torque needed.

Looks so easy

Как отличить оригинал?

Ну хоть у кого-то женщины на видео нормальные есть, и руки у которых из нужного места растут😆 А 4 часа ждать, это вообще нельзя двигать ничего делать? А если подъёмник нужен?

Love that platinum blonde hair and womanly nose, yowza!

Niçin 4 saat bekle diyorsunuz. 4 hours ?

That seemed so effortless, so why does a shop say it takes 8 to 10 hours?

I wanna work where she’s working 😂😂😂😂😂

🤔🧐👍

She got a nose job.

I was actually most impressed by how she pulled the packaging off the new gasket without immediately dropping it onto the floor.

This is a dumb video that is not helpful at all. There were no tips, and you can hardly call it a tutorial if you don't provide any instruction.

Victoria is lucky 🍀 she has such a clean engine to work on 🥰

Ya right! Ridiculous video.. she had that in and out in 2 minutes. If this was about the spray she was using. Then ok.for anyone who never done this before ..stop and call someone or go garage. This isn’t like changing a tire. It can be extremely frustrating for even the most experienced mechanics. Now consider you don’t have a lift or a crew of people to take everything off to get to the manifold and loosen all your bolts for you and steam clean the engine before you even attempt it .. you most likely will break bolts . Then your screwed because they will be hardened and nearly impossible to drill out without a carbide bit or to burn it out. Bottom line this isn’t easy at it looked and you could end up much worse off then when you started

The title on the bus "Штаб пожаротушения" - control point of fire extinction.

OK 👌 thanks it's very good

bought a Victor Reinz full gasket set last year for a BBC. I like to compare new parts with old parts. Just something I learned the hard way. The rear main seal did not look right. I put it together on the crank and found that the seal lips did not even touch the crank. If I had just put this motor together and put it back in the car, I would have had a massive oil leak. I tried to contact Victor reinz and got NO response. All I could think was how many guys put motors together with this (wrong) seal. I never buy Victor reinz anything anymore. Anyone (whoever put the kit together) can make a mistake. My problem is Victor reinz simply did not care.

I bought a Victor Reinz full gasket set last year for a BBC. I like to compare new parts with old parts. Just something I learned the hard way. The rear main seal did not look right. I put it together on the crank and found that the seal lips did not even touch the crank. If I had just put this motor together and put it back in the car, I would have had a massive oil leak. I tried to contact Victor reinz and got NO response. All I could think was how many guys put motors together with this (wrong) seal. I never buy Victor reinz anything anymore. Anyone (whoever put the kit together) can make a mistake. My problem is Victor reinz simply did not care.

Can anyone tell me what she wiped it with ?

Что за средство в распылителе?

Find this video to be BS💯 Has anybody else seen how extremely clean this car is 🤷 Look at how clean the engine bay before she took it off 😱 no car is not clean 🤦👎

what is tip cleaner is it a gazoline or what

PLS..... Do we need a threadlocker at Bolts to prevent oil leak

Do we need Threadlocker at threads like loctite to prevent oil leake

what type of cloth in the video recommended for cleaning narrow slots

Perfect job >> but i have 2 questions pls

What a waste of time, it lasts 7 minutes, only watched for a minute and i had enough.

Silent movie....I was wondering when Charlie Chaplin would appear. The next episode will be point of view, the Technician will speak, and wear a blindfold.

Dont we have to seal a couple of edges with a sealant?